De presentatie wordt gedownload. Even geduld aub

De presentatie wordt gedownload. Even geduld aub

Choose your Ecotap Load balancer type A A Direct measurement V3.6 Indirect measurement 1.

Verwante presentaties


Presentatie over: "Choose your Ecotap Load balancer type A A Direct measurement V3.6 Indirect measurement 1."— Transcript van de presentatie:

1 Choose your Ecotap Load balancer type 669010 0-32A 669015 32-63A Direct measurement V3.6 Indirect measurement 1

2 Settings Wiring Choose installation type 2

3 123 mm 80 mm 201 mm Direct measurement 669010 0-32A 669015 32-63A 3

4 Safety regulations Before you install the charging st ation, you must make sure the location is safe for all bystanders. NEVER allow children onto this w orksite. Never allow ANYONE who has no thing to do with the work onto the worksite. Never be distracted while you are performing the work. Make sure you maintain a heal thy posture at all times while doing the work. Do not leave any tools or charging station component s unattended. Make sure any tools you are u sing are clean and dry. Make sure that the charging st ation, tools and components will stay dry when it is raining. 4

5 4 5 6 N 1 2 3 N 5 If there are two blue wires on the load balancer, connect one blue wire to the groups Groups

6 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB 6

7 60 Ω 7 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB

8 8

9 Indirect measurement Coils not included 9

10 SDM60MCT V2 10

11 Safety regulations Before you install the charging st ation, you must make sure the location is safe for all bystanders. NEVER allow children onto this w orksite. Never allow ANYONE who has no thing to do with the work onto the worksite. Never be distracted while you are performing the work. Make sure you maintain a heal thy posture at all times while doing the work. Do not leave any tools or charging station component s unattended. Make sure any tools you are u sing are clean and dry. Make sure that the charging st ation, tools and components will stay dry when it is raining. 11

12 12

13 13 L1L2L3NPE L1L2L3NPE S1 S2 P1 P2 C1 S1 S2 P1 P2 C2 S1 S2 P1 P2 C3 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB 120 Ω 13 14 ADRESS 3 e otap

14 14 L1L2L3NPE L1L2L3NPE S1 S2 P1 P2 C1 S1 S2 P1 P2 C2 S1 S2 P1 P2 C3 ADRESS 3 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB e otap

15 L1 L2 L3 N Residual Current Device (RCD) Aardlekautomaat (ALA) Power for meter LA5L NA6N 15

16 16 L1 L2 L3 L1L2L3 P2 P1 P2 P1 P2 P1

17 L1 L2 L3 S1 L2 L3 L1 S2 17

18 18 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB

19 60 Ω 19 Or/WhtOrngBrownMeter A +B -GEastron A -B +CABB

20 20

21 21

22 The Ecotap load balancer works with the following settings. BAUDRATE:9600 ADRESS:3 PARITY:NONE STOPBIT:2 * CT2:5A * CT-RATE:Depending on the coil * Pay attention! these settings can only be adjusted once! 22

23 0000 PASS 000 1 Hold down 3 sec PASS 000 1 Hold down 3 sec 23

24 SET addr 001 SET addr 01 0 SET addr 0 1 Hold down 3 sec RS485 / Mbus primary Addres 24

25 SET Addr 00 3 SET Addr 00 3 SET addr Good Hold down 3 sec RS485 / Mbus primary Addres 25

26 SET addr 003 SET Baud 9.6 Set Baud 9.6 Hold down 3 sec RS485 / Mbus primary Addres Baud rate 26

27 SET Baud Set Baud good Hold down 3 sec Baud rate SET Baud 9.6 Baud rate 27

28 Set Parl none Set Stop 2 Note: Only when the parity is NONE, the stop bit can be changed to 2 Parity Stop bits 28

29 100 / 5A 100 = CT RATE 5A = CT2 RATE The CT options set the Secondary Current (CT2 5A or 1A) of the Current Transformer (CT) that are used with the meter 29

30 Set Ct2 5 Secondary Current Set Ct2 Set Ct2 5 Set Ct2 Hold down 3 sec Secondary Current 30

31 Set Ct2 good Secondary Current Set Ct2 5 Secondary current 31

32 Set Rate 0001 Set Rate 001 Hold down 3 sec The CT Rate is the CT Primary divided by the CT Secondary. For Example: 200/5A Current Transformers - 200÷5=40, so the CT Rate would be 0040 and the CT2 would be 5. CT Rate 32

33 Set Rate 001 Set Rate 0 01 0 CT Rate 100 ÷ 5 = 20 33

34 Set Rate 00 1 2 Set Rate 002 Hold down 3 sec CT Rate 100 ÷ 5 = 20 34

35 Set Rate good CT Rate 100 ÷ 5 = 20 35

36 Set Rate 0020 Set Pt2 400 Pt Rate 0001 Secondary voltage (100V to 500V) Energy represented by each pulse CT Rate 36

37 Set rly Pulse output Set Rate 001 SET Puls 200 Energy represented by each pulse The energy monitored can be active or reactive and the pulse width can be selected as 200, 100 or 60mS. 37

38 Set Dit 60 Current and power readings intehrated for maximum demand measurements in minutes Set LP 0 SYS 3p4 Backlit lasting time Type of power supply being monitored 38

39 CLr Reset the maximum demand value of current and power Set Pass 1000 Set Sys cont Set new passcode Revurse connected current inputs correction set-up 39

40 Check if the coils are connected correctly 0000 004.3 40

41 0.043 -0.043 If the minus sign appears before a number, that coil is incorrectly connected to the S1 and S2 L1 L2 L3 S2 S1 L3 41

42 42

43 Kruisbroeksestraat 23 5281 RV Boxtel +31 (0) 411 – 210 210 info@ecotap.nl www.ecotap.nl


Download ppt "Choose your Ecotap Load balancer type A A Direct measurement V3.6 Indirect measurement 1."

Verwante presentaties


Ads door Google